Q: Will this fit my Typhoon QS 500 4K ? It looks the same other than another contact window. Thanks

Asked by: David Martin - 2/3/2021
A: Unfortunately this will not fit the Q500 since the mount is slightly different.
Was this answer helpful?  2 of 3 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (5/11/2021)

Q: This item says out of stock and “in production”. Does that mean you will be getting more?

Asked by: Erin Ash - 8/5/2020
A: Yes, we are expecting more mount sets to come in. They are a hot item and sell out rather quickly after they come in.
Was this answer helpful?  1 of 2 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (11/17/2020)

Q: the picture only shows 2 of the 4 retaining pins is that all this comes with? I am in need of 4 pins and the clips.

Asked by: Casey Owens - 3/1/2019
A: The mount set only comes with two, because it is only suggested to have two retaining pins one on each side diagonally. We do not sell the retaining clips separately, they only come with the mount set.
Was this answer helpful?  4 of 5 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (3/1/2019)

Q: i looked but cant find the lower part of Part Number:YUNCGO3P105 ?, can you help, thanks

Asked by: THONG - 11/21/2017
A: You can find the bottom dampening plate in the link below,

https://www.vertigodrones.com/Yuneec-CGO3-Bottom-Dampening-Plate_p_448.html
Was this answer helpful?  1 of 3 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (4/20/2018)

Q: Will this mount set , the shock dampers fit the Q500 as well???

Asked by: Phil K - 11/18/2017
A: The Q500 has different dampers than the Typhoon H CGO3+ mount set. You can find the mount set with dampers for the Q500 with the link I have provided below.

https://www.vertigodrones.com/Yuneec-CGO3-Mount-Set-Q500-4K_p_183.html
Was this answer helpful?  1 of 2 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (3/16/2018)

Q: Is there 4 of the pins and the washer clips with this kit ?

Asked by: Earl Mannette - 10/23/2017
A: This kit comes with 2 pins and 2 washer clips.
Was this answer helpful?  3 of 5 Customer(s) found this Answer helpful.
Answer provided by: Amanda Saul (3/15/2018)

Q: Can you use four pins to make it more secure or is there a reason why there is only two?

Asked by: kevgk044 - 9/17/2017
A: There is no logical reason Yuneec chose not to include 4 retaining pins. Installing 4 pins will not necessarily prevent damage but will not adversely affect anything.
Was this answer helpful?  8 of 10 Customer(s) found this Answer helpful.
Answer provided by: Andrew (9/18/2017)

Q: there are four holes but you show only two pins? John Morandi

Asked by: John - 8/16/2017
A: The pins are installed on opposite diagonal corners. Only two are shipped from the manufacturer.
Was this answer helpful?  1 of 4 Customer(s) found this Answer helpful.
Answer provided by: Andrew (8/21/2017)

Q: Can you just purchase the retaining pins? My mount is fine, I just need the washers the lock the pin in place.

Asked by: Mark - 8/7/2017
A: We are working with Yuneec to make the pins available. Please check back in the near future for availability.
Was this answer helpful?  4 of 5 Customer(s) found this Answer helpful.
Answer provided by: Andrew (8/11/2017)

Q: Will this mount fit the Yuneec typhoon Q500+ ?

Asked by: hightv - 7/5/2017
A: No. The mount set you are looking for can be found at the following link: https://www.vertigodrones.com/Yuneec-Mount-Set-CGO3_p_183.html
Was this answer helpful?  1 of 2 Customer(s) found this Answer helpful.
Answer provided by: Andrew (8/6/2017)

Q: Is there 4 pins or just 2 that hold the camera bracket together because mine only has 2 I just bought new?

Asked by: REX DICKEY - 5/16/2017
A: Hello SIr,

Only two pins are needed to secure the slip ring wires from damage, each on an opposite corner
Was this answer helpful?  4 of 6 Customer(s) found this Answer helpful.
Answer provided by: Spencer (5/17/2017)

Q: I see whats wrong, the base plate is the part that need, the part that slides on the drone broke the slides I need the the base plate, when I crashed it broke the slides that attach it to the drone, I'm looking at the base plate on your website, my problem is I can't seem to figure out how the base plate comes away from the wiring and contacts. Is this something I can do without taking it in for repairs? So far I've got the washers off the two pins, haven't gotten any farther in the last hour. Any help with this would be appreciated. The drone is a Typhoon H with a CGO3 +

Asked by: Paul Couture - 5/11/2017
A: Hello Paul,

If you are looking to swap out your mountset for the CGO3+, you will need to remove the three silver screws that are holding the contact plate in its place, once you loosen this panel, the contact plate and wiring can be separated from the top dampening plate and swapped out
Was this answer helpful?  5 of 6 Customer(s) found this Answer helpful.
Answer provided by: Spencer (5/16/2017)

Q: Hi do you have this in stock and ship to Australia? How much.

Asked by: Devin - 3/28/2017
A: Current stock is displayed on the product page. We shop world wide. Prices in USD with shipping are available during checkout before payment.
Was this answer helpful?  0 of 1 Customer(s) found this Answer helpful.
Answer provided by: Andrew (4/8/2017)

Q: bought typhoon h , only two of 4 mounts are connected, is this normal?

Asked by: j - 3/11/2017
A: Yes, this is how they are shipped from the factory. Two is sufficient to prevent wire damage in the even of a hard landing.
Was this answer helpful?  3 of 3 Customer(s) found this Answer helpful.
Answer provided by: Andrew (3/20/2017)

Q: Does this come with the pins and locks to prevent the camera from falling off?

Asked by: Doug Gleason - 7/13/2016
A: Yes. It now includes the plastic pins.
Was this answer helpful?  6 of 8 Customer(s) found this Answer helpful.
Answer provided by: Andrew (8/3/2016)